- 530 INR
- 530.00 - 530.00 INR
LATAFIX 305 Floor and Wall Thin Set Adhesive PRODUCT DESCRIPTION LATAFIX 305 Floor and Wall Thin Set adhesive is a bagged cementitious powder to be mixed with water for installing ceramic tile and natural stone using the thin-set method of installation. Application Can be used for interior applications on floors and walls over masonry, concrete, mortar beds and cement plaster Advantages Dual Purpose for walls and floors Easy to use Plastic Consistency Consistent quality, ready to use Proven performance Suitable SubstratesCement Mortar Beds Ceramic Tile and Stones Cement Plaster Brick Masonry Cement Terrazzo ^When mixed with LATICRETE 73 Crete Admixture. Packaging - 20 kg and 50 kg bag Colour: Grey Coverage Approx 55 - 60 sft per 20 kg bag when trowelled with 1/4 x 1/4 (6mm x 6 mm) square notch trowel Coverage will vary depending on trowel notch size, type and size of tile and substrate Shelf Life Factory sealed bags of this product are guaranteed to be of first quality for one (1) year if stored off the ground in a dry area. High humidity will reduce the shelf life of bagged product. Limitations Use LATAPOXY 300 Epoxy Adhesive for installing green marble or water sensitive natural stone and agglomerates. Adhesives/mastics, mortars and grouts for ceramic tile, paver brick and stone are not designed as replacements for waterproof membranes. When a waterproof membrane is required, use a LATICRETE 9237 / Hydroban Waterproof membrane. Note: Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L span length. Cautions Contains Portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water. Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas. Protect finished work from traffic or damage by other trades for an extended period of time during cold weather conditions. At room temperature conditions 70 F (20 C), protect overnight. Keep out of reach of children. TECHNICAL DATA Applicable Standard ANSI A 118.1 1999; EN 12004 & ISO 13007 Performance Properties LATAFIX 305 Floor and Wall thinset adhesive mixed with Water Test Test Method Results Shear Bond Porcelain Tile 28 day cure ANSI A 118.1- 1999;F-5.2 200 psi (1.3 MPa) Shear Bond Porcelain Tile ANSI A118.1- 1999; C-5.2.3 170 psi (1.1 MPa) Water immersion Compressive Strength ANSI A118.4- 1999; F-1 (modified) 2000 psi (13.7 MPa) Complies to EN: C1T Working Properties at 700 F ( 21 0 C ) LATAFIX 305 Floor and Wall thinset adhesive when mixed with water. Open Time Approx 20 minutes Pot Life Approx 4 hours Time to Heavy Traffic 16-24 hours Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions. INSTALLATION Surface Preparation All surfaces should be between 40 F(4 C) and 90 F(32 C) and structurally sound, clean and free of all dirt, oil, grease, loose peeling paint, laitance, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with LATICRETE Latex Portland Cement underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. New concrete slabs shall be damp cured and 28 days old before application. *No minimum cure time for concrete slabs when thin-set mortar is mixed with latex additive. All slabs must be plumb and true to within (6mm) in 10 ft(3m). Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI Specification AN-3.8 Requirements for Expansion Joints or TCA Detail EJ171 Expansion Joints . Do not cover expansion joints with adhesive, tile or stone. Mixing Stir LATICRETE admix thoroughly before use. Place clean, potable water or LATICRETE latex admix into a clean pail. Add LATAFIX 305 powder to the liquid. Use approximately 6L of water for 20 kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow adhesive to slake for 5-10 minutes. Adjust consistency if necessary. Remix and apply with the proper sized notched trowel. Application Apply adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Use the proper sized notched trowel to insure full bedding of the tile. Spread as much adhesive as can be covered with tile in 10 minutes. Back butter large tiles (> 12 x12 ) to provide full bedding and firm support. Place tiles into wet, sticky adhesive and beat in using a beating block and rubber mallet to imbed tile and adjust level. Check adhesive for complete coverage by periodically removing a tile and inspecting bedding adhesive transfer onto back of tile If adhesive is skinned over (not sticky), remove and replace with fresh adhesive. Grouting Grout installation after a minimum of 24 hours curing time at 70 F(21 C). Grout with LATICRETE Sanded or Unsanded Grout mixed with LATICRETE 1776 Grout Admix Plus . For maximum stain resistance use LATAPOXY SP-100 Stainfree Grout or SpectraLOCK Pro Premium Grout. Cold Weather Note: The setting of Portland cement adhesives and grouts are retarded by low temperatures. Protect finished work for an extended period when installing in cold weather. For faster setting, use LATICRETE 252 Fast Set or LATICRETE 73 Rapid admix with LATICRETE 111 Crete filler powder. Do not set tile when surface temperature is below freezing or when substrate is frozen. Hot Weather Note: The evaporation of moisture in Portland cement adhesives and grouts is accelerated by hot, dry conditions. Apply to dampened surfaces and protect freshly spread adhesive and finished work when installing in temperatures over 95 F (35 C).
- North India
Shop No.10, Kaushik Complex, First Floor, Near The City Pride Banquet Hall, Hoshiyarpur, Sec.51, Metro piller no. - 223,, Noida, Uttar Pradesh, 201301, India